[RESOLVED] Ford DCL communication protocol standard

Sergio2007

Sergio2007

New Member
#41
Hello MrTdude

Of course that it is possible.
Send me a PM or mail and I will send you as soon as I can.
What are you planning to do with DCL ?? and where are you from ??

Best Regards.

Sergio
 
Last edited:
M

MrTDude

New Member
#42
Sergio,

I am new to this message board, how do I PM or mail. I don't see these options on my menu?

Regards,
MrTDude
 
M

MrTDude

New Member
#44
Sergio,

I just signed up today. Any idea on how long it will be before I can contact members?

Regards,
MrTDude
 
Sergio2007

Sergio2007

New Member
#45
Maybe you can download it from opendiag.

What are you planning to do with DCL ?? and where are you from ??

Regards,
Sergio
 
M

MrTDude

New Member
#46
Sergio,

I am a student looking and have an interest in getting information from my old 1995 Ford. I am in the US.

I can try and download from dialog if you think it may work. Thank you for the help.

MrTDude
 
M

MrTDude

New Member
#48
Sergio,

I am in the process of trying to verify my account so I have access to the opendiag link you provided above. Thank you.

It looks like there are problems with Yahoo server right now. I will have to try again later.

Regards,
MrTDude
 
Last edited:
Sergio2007

Sergio2007

New Member
#49
Maybe you can suscript some temporal mail to send me by this board.

It is a little complex board for me.
 
Last edited:
M

MrTDude

New Member
#50
Sergio,

I have signed up for opendiag, I'm not sure how long it takes to get access. I will try back later today or tomorrow. I will then try to download you DCL information. Thank you.

MrTDude
 
Sergio2007

Sergio2007

New Member
#51
In opendiag you have to wait a max time of 7 days, because they process suscriptions once a week.

Best Regards MrTDude.

Sergio
 
M

MrTDude

New Member
#52
Hi Sergio,

I was doing more internet searching for DCL information and noticed that you had posted comments on another forum a while back. I have sent an email to the ciudad email address hoping that it is still valid. If ithe address is still in use, can you respond to the email address I sent to you? Thank you.

Regards,
MrTDude
 
S

Steve2009

New Member
#53
MrTDude,

Send me a comment from my web page and I'll tell you where these are to be found.

Steve
 
S

Steve2009

New Member
#55
In case you are interested, I've updated my EEC-IV web page to show my progress with DCL. Sorry that there isn't much there yet - I have only been working on this for a few days, but I will post updates as I make progress.

http://158.143.56.200/~steve/eeciv/

Steve
 
F

flying_greg

New Member
#56
Looks like this thread is a few months old, but hopefully you still look at it.

I am wondering if any of you might have the pinout for the 6-pin DLC connector?
From what I have found on the internet I have 1=SIG RET, 2=?, 3=FUEL PUMP, 4=?, 5=STO, and 6=?

From reading this thread it looks like 2 of the 3 unknown pins will be DLC+ and DLC- ?

Thanks!
 
F

flying_greg

New Member
#58
SWEET!!!!!

That's EXACTLY what I was looking for!! Now I can design some a suite for testing!

Thanks A LOT!
 
Sergio2007

Sergio2007

New Member
#60
Well, here is another picture with different polarity in DCL (+) and DCL (-).
May be You will have to test tension levels with a multitester to be sure.



Best Regards,

Sergio

PD: Where are you from flying_greg ??

--
 
Last edited:

Associates