overclocking the amd k6-2 350 to 368mhz

G

Goffenheimer

New Member
#4
I went to that website and found the manual to the board you have. You need Adobe Acrobat to read it. If you don't have that here are some charts I made that might help you out.


DIP Switch (SW2) selects Bus Clock Multiplier

|Multiplier|SW2-P4|SW2-P5|SW2-P6|
|--x 2.0---|--OFF-|--OFF-|--ON--|
|--x 2.5---|--OFF-|--ON--|--ON--|
|--x 3.0---|--OFF-|--ON--|--OFF-|
|--x 3.5---|--OFF-|--OFF-|--OFF-|
|--x 4.0---|--ON--|--OFF-|--ON--|
|--x 4.5---|--ON--|--ON--|--ON--|
|--x 5.0---|--ON--|--ON--|--OFF-|
|--x 5.5---|--ON--|--OFF-|--OFF-|


DIP Switch (SW2) selects CPU Bus Clock

|Bus Clock|SW2-P1|SW2-P2|SW2-P3|JP13 |
|--60MHz--|--ON--|--ON--|--ON--|Open |
|--66MHz--|--ON--|--ON--|--OFF-|Open |
|--68MHz--|--ON--|--OFF-|--ON--|Open |
|--75MHz--|--OFF-|--ON--|--ON--|Open |
|--83MHz--|--OFF-|--ON--|--OFF-|Open |
|--95MHz--|--OFF-|--OFF-|--ON--|Open |
|--100MHz-|--OFF-|--OFF-|--OFF-|Open |
|--105MHz-|--ON--|--OFF-|--OFF-|Close|
|--110MHz-|--ON--|--OFF-|--ON--|Close|
|--115MHz-|--ON--|--ON--|--OFF-|Close|
|--120MHz-|--ON--|--ON--|--ON--|Close|


DIP Switch (SW1) selects CPU voltage

|CPU Volt-age|SW1-P1|SW1-P2|SW1-P3|
|----2.0V----|--OFF-|--OFF-|--OFF-|
|----2.1V----|--ON--|--OFF-|--OFF-|
|----2.2V----|--OFF-|--ON--|--OFF-|
|----2.3V----|--ON--|--ON--|--OFF-|
|----2.4V----|--OFF-|--OFF-|--ON--|
|----2.5V----|--ON--|--OFF-|--ON--|
|----2.6V----|--OFF-|--ON--|--ON--|
|----2.7V----|--ON--|--ON--|--ON--|
|----2.8V----|--OFF-|--OFF-|--OFF-|
|----2.9V----|--ON--|--OFF-|--OFF-|
|----3.0V----|--OFF-|--ON--|--OFF-|
|----3.1V----|--ON--|--ON--|--OFF-|
|----3.2V----|--OFF-|--OFF-|--ON--|
|----3.3V----|--ON--|--OFF-|--ON--|
|----3.4V----|--OFF-|--ON--|--ON--|
|----3.5V----|--ON--|--ON--|--ON--|

nice huh?

------------------


-Goff



[This message has been edited by goffenhiemer (edited 01-07-2000).]
 
J

jreclark

New Member
#6
Now That is a clocker board man!! I think you
may see 400mhz no problem. Set to
100mhz\4.5x\2.3V. This will work. You may get it to stabalize at 2.2v but I wouldn't count on it.
 
J

jreclark

New Member
#7
Now That is a clocker board man!! I think you
may see 400mhz no problem. Set to
100mhz\4.5x\2.3V. This will work. You may get it to stabalize at 2.2v but I wouldn't count on it.
 
J

jreclark

New Member
#8
Now That is a clocker board man!!
I think you may see 400mhz no problem. Set to
100mhz\4.5x\2.3V. This will work. You may get it to stabalize at 2.2v but I wouldn't count on it.
 
G

Goffenheimer

New Member
#9
I made some edits to the charts, I hope you can read them now.

------------------


-Goff