P4 2.2 @ 2650MHz :)

[jankerson]

Well Had to reflash the bois because the fixed PCI/AGP multiplier wasn't working. That's why I couldn't get any higher than 115fbs before. I checked because I couldn't figure out what the hell was going on. Opened Sandra and saw that the AGP and PCI bus wasn't staying at 66/33.

Running at 22x120 for 2650MHz @ 1.8v.

3D Mark 2001se 12099 Gforce4 TI 4400
http://service.madonion.com/compare?2k1=3623685

Sandra 2002

Cpu

Dhrystone 5026 mips
Whetstone 1385/3216 MFLOPS

Multimedia

Integer 10520 it/s
Floating 12800 it/s

Memory

Inter 3004 MB/s
Float 3003 MB/s


Not too bad 450mhz overclock on air sofar. Thermaltake Volcano 7+, Artic Silver 111.

Temps 45C by Abit Hardware Monitor.

------------------
P4 2.2GHZ @ 2650MHz, 45C, Abit TH711, 512mb PC800 RDRAM, 60g WD, Lite-On 16x DVD, Gforce4 TI 4400, SB Live 5.1, 431w PS
Dual P3 1000, 1g PC 133, 550w PS, Adaptec SCSI,18g,36g Cheetahs

[This message has been edited by jankerson (edited 06-05-2002).]

[This message has been edited by jankerson (edited 06-05-2002).]

[Dave_B]

I would think you should be doing a little better on 3DMark2001. I've got a Prolink PixelView GeForce4 Ti4200 64MB AGP running on an Epox 4GA4+ i845G mobo with a P4 2.0A @ 2.6 GHz. My score is a little higher at 11,491. I would think with the Ti4400 vs. my Ti4200 and RDRAM vs. DDR you would do better. But maybe you just need to get your FSB up a little more. Also my Ti4200 is overclocked at 315/615.

[jankerson]

Originally posted by Dave_B:
Also my Ti4200 is overclocked at 315/615.

Dave,

I am running my TI 4400 at default, that's the difference. I haven't overclocked it yet.


------------------
P4 2.2GHZ @ 2650mhz, 45C, Abit TH711, 512mb PC800 RDRAM, 60g WD, Lite-On 16x DVD, Gforce4 TI 4400, SB Live 5.1, 431w PS
Dual P3 1000, 1g PC 133, 550w PS, Adaptec SCSI,18g,36g Cheetahs

[jankerson]

Dave_B,

Just for you Bud

3Dmark 2001se 12099

Ti 4400 @ 300/650
http://service.madonion.com/compare?2k1=3623685

That score put's me well into the top 20 overall.

------------------
P4 2.2GHZ @ 2650mhz, 45C, Abit TH711, 512mb PC800 RDRAM, 60g WD, Lite-On 16x DVD, Gforce4 TI 4400, SB Live 5.1, 431w PS
Dual P3 1000, 1g PC 133, 550w PS, Adaptec SCSI,18g,36g Cheetahs

[This message has been edited by jankerson (edited 06-05-2002).]

[Dave_B]

See I've inspired you to go for the brass ring. Now get that CPU going before I do the voltage mod on my Epox and go for 2.8 GHz!

[jankerson]

Originally posted by Dave_B:
See I've inspired you to go for the brass ring. Now get that CPU going before I do the voltage mod on my Epox and go for 2.8 GHz!

HAHA, Got luck and have fun.

I already turned my 2.2 up to 2716mhz 22x123 @ 1.85v and it booted into Windows fine, but it's not stable.

Don't think I want to crank up the Voltage any higher than I have it now (1.8v) and run it for very long.



------------------
P4 2.2GHZ @ 2650mhz, 45C, Abit TH711, 512mb PC800 RDRAM, 60g WD, Lite-On 16x DVD, Gforce4 TI 4400, SB Live 5.1, 431w PS
Dual P3 1000, 1g PC 133, 550w PS, Adaptec SCSI,18g,36g Cheetahs

[Dave_B]

With good cooling these low voltage CPUs are pretty tough. I had Athlon 1.4 and XP 1800+ CPUs running at over 2.0V for months with no problems. And my previous P4 1.6A didn't have any problem (other than a high temp) with 2.0V. Anyway, at the rate you're upgrading it only has to last a couple of weeks anyway.

[Dave_B]

Comin' back at ya! I got the P4 2.0A running stable at 2.64 GHz, set the Ti4200 @ 315/620, and tweaked some of the AGP settings and my 3DMark2001 score is up to:

11,986

Not quite the magic 12,000 figure, but pretty close!

[jankerson]

Dave_B,



Just alittle more.

I can boot into Windows at 2716MHz, it will run all the Sandra benchmarks, but not 3DMark2001se yet. Soon though.

I burned the CPU in at 2540 @ 1.75v for 24 hours yesterday using Prime 95. I will give it a few more days then see if I can get anymore out of it.


------------------
P4 2.2GHZ @ 2650mhz, 45C, Abit TH711, 512mb PC800 RDRAM, 60g WD, Lite-On 16x DVD, Gforce4 TI 4400, SB Live 5.1, 431w PS
Dual P3 1000, 1g PC 133, 550w PS, Adaptec SCSI,18g,36g Cheetahs

[Big Lar]

The 2.2 runs very well if you cool it off a bit more I have mine running @ 2940 with water cooling.

------------------
Help me get this Boot outta my azz!!!!

[jankerson]

Maybe, but I don't want the hassle and don't want to bother with Water cooling.



------------------
P4 2.2GHZ @ 2650mhz, 45C, Abit TH711, 512mb PC800 RDRAM, 60g WD, Lite-On 16x DVD, Gforce4 TI 4400, SB Live 5.1, 431w PS
Dual P3 1000, 1g PC 133, 550w PS, Adaptec SCSI,18g,36g Cheetahs

[ol' man]

That is nice jankerson. i would like to see you hit a little higher though

What are you using as a HS and is your IHS lapped good and flat or better yet remove the IHS!

------------------
1.2Ghz cel-t @ 1.6GHz/1.65v

Off Topic Central

[jankerson]

I am using a Thermaltake Volcano 7+ and it does sit good and flat.

------------------
P4 2.2GHZ @ 2650mhz, 45C, Abit TH711, 512mb PC800 RDRAM, 60g WD, Lite-On 16x DVD, Gforce4 TI 4400, SB Live 5.1, 431w PS
Dual P3 1000, 1g PC 133, 550w PS, Adaptec SCSI,18g,36g Cheetahs

[jankerson]

P4 2.2 @ 2694MHz

3DMark 2001SE 12,409

TI 4400 @ 300/650
http://service.madonion.com/compare?2k1=3665904



------------------
P4 2.2GHZ @ 2650mhz, 45C, Abit TH711, 512mb PC800 RDRAM, 60g WD, Lite-On 16x DVD, Gforce4 TI 4400, SB Live 5.1, 431w PS
Dual P3 1000, 1g PC 133, 550w PS, Adaptec SCSI,18g,36g Cheetahs